![]() ![]() In my plans, I left a small gap between the top of the 2×2″ boards and the top of the horizontal planks – this was done in case you wanted to add a shelf to your DIY Christmas tree stand to raise it off of the ground (it gives your tree another ~18″ of height). Sand smooth and it’s ready for paint (or stain). I believe this is the photo of my way-to-big version, but you get the idea. Set your mitre saw angle to 5° and cut.Īttach the long boards to the sides of the 2×2 posts, covering the end cuts of your shorter boards. (The same as we did in step 1) This will give you your 5° angle. Mark 3/8″ on either side of what will be your top board and draw a line from the mark down to the bottom corner of the base board. (Reset your mitre saw to 0) and cut 8 boards to 21″ long. Now it’s time to cut and attach the long sides of your DIY Christmas tree stand. If you did understand what I was trying to say, you should have two pieces that look like the above photo. See how the angled cut makes the 2×2 line up with the outside edge of your long boards and the bevel cut leans those boards inwards when standing.Ĭlick over to Jaime’s plans if that was a mess of words and you have no idea what I’m talking about. Repeat on both sides, lining up your 2×2 with the edge of your long boards. The 5° angle will keep it lined up with the angled sides of your long boards. The 2×2 should lean back but remain upright (if it tips forwards, you’ve got it backwards. Leave your mitre saw angled at 5° and move your bevel to 5° – again, if it’s easier to visualize, mark 3/8″ up on one side of your 2×2 and then draw a line from that mark to the bottom corner opposite.Īttach the 2×2 board to the back of your long boards with 2″ wood screws. Once you have the line drawn on all four boards, it’s easier to know where your 5° angle cuts should be. To make life easier, I lined up my boards, marked the top board in ¾” on either side and then drew a straight line from the ¾” mark to the bottom corner of the base board. Make a 5° angle cut on your mitre saw on both short ends of the boards. I knew I was going to paint it, so wood type etc didn’t really matter to me – if you’re planning on staining yours, you’ll want to have nice, matching, boards.įirst up, line up your 19 ¼” boards as below. I made my DIY Christmas tree stand entirely out of scrap wood – so you’ll see my wood is different colours and in some cases, slightly different thicknesses. If you don’t have a mitre saw that can cut angles and bevels, don’t worry – I’m including measurements so you can still join in. This project is going to give you a little practice with the angles and bevels on your mitre saw. (the tree stand that came with my tree is 23″ by 23″ when the legs are open in their “X” pattern – I believe this is standard for most 7.5′ trees) Please measure your tree stand before starting to make sure my plans aren’t too big or too small for your tree. Once I guesstimated the size of my tree stand – and then built a giant monstrosity that could hold two trees – and then the second time I did it right. I’m showing my building plans for those of you (like me) that found Jaime’s a bit confusing, and/or needed a DIY Christmas tree stand for a larger tree.įirst off, I will admit that I built this thing twice… You can put your woodworking skills to the test by making a "box" for your Christmas tree or you could simply create a knitted collar that will make your entire room feel cozy.This DIY Christmas tree stand is actually a knock-off of Jaime’s over at, but I had to adjust it a bit to fit my larger tree base and I wanted my tree to be off of the ground – so I needed it to have a shelf insert as well. Ahead, you'll find tons of ideas for decorative tree stands and tree collars that will match any style, whether you love vintage Christmas decorations or a more modern look. Try making a stand of your own that will not only beautify your tree, but keep it sturdy and in place as well. Sure, displaying all types of Christmas trees on the plastic stands you buy at the store is an option, but there are so many beautiful homemade alternatives. Sure, it requires a little extra time to make, but a homemade element is always worth it. After you've gathered those homespun decorations and picked out a Christmas garland, there's one final element you'll need for the heavy lifting: pretty DIY Christmas tree stands! These are absolutely necessary to help bring together a festive display of Christmas decorations. She's definitely on the DIY ornaments train, preferring ones she's had since childhood or sentimental gifts over a big set of store-bought ornaments. ![]() ![]() If you're like Ree Drummond, you have opinions about Christmas tree decorations. ![]()
0 Comments
Leave a Reply. |